ES Windows Door Installation Nationwide

ES Windows Door Installation: The Fort Lauderdale Owner’s Guide

ES Windows door installation in Fort Lauderdale typically runs $950 to $2,400 for a full replacement, and most swaps are completed in one day once the door is in hand. We stock the common ES Windows door hardware and threshold components on our trucks, so a good number of these jobs are done on the first visit. Where homeowners usually find the problem is the corner: a sagging hinge, a dragging sweep, or a door that has started catching on the jamb because the original install was never shimmed right, or because ten years of Florida humidity have done their work on the frame.

Call (754) 354-3671

We’re an independent window and door contractor, not an ES Windows dealer or warranty center. We work on ES Windows products every month and we carry the parts that fail most often here in Broward County. Spencer Odell has been measuring, installing, and warranting doors across Fort Lauderdale for the better part of two decades, and the crew has seen every ES Windows door configuration that coastal Florida can throw at a house.

Key Takeaways:

• Typical installed cost for an ES Windows door replacement in Fort Lauderdale: $950 to $2,400
• Most single-door swaps finish the same day the door arrives
• We carry common ES Windows hinges, sweeps, thresholds, and roller assemblies on the truck
• Written price in your hands before any work starts, every time
• Every installation is backed by the 365-Day Done Right Promise: if it’s not right, we make it right, no argument needed

Which ES Windows Models This Applies To

ES Windows builds three door families we see regularly in Fort Lauderdale: the ES700 series (their mid-range impact-rated line), the ES900 series (heavier, used on larger openings and waterfront homes), and their basic non-impact ES300. The compatibility gotcha most homeowners hit is this: ES700 and ES900 hinges are not interchangeable. The ES900 uses a taller leaf with a heavier barrel, and if you order an ES700 hinge for an ES900 door, the screw holes won’t line up and the leaf sits proud of the jamb. We match by the number stamped on the hinge face and by measuring the leaf height with calipers, not by guesswork.

The second thing we check is the threshold: ES Windows has used three different threshold profiles since 2012, and the older profile is no longer in production. When an older threshold is cracked or the vinyl cap has split, we mill a matching profile from aluminum stock rather than forcing a new-style threshold that would change the reveal on the door. OEM parts are the first choice when they are still available; for discontinued profiles and hardware, we use quality aftermarket equivalents that we have tested in Florida conditions. An aftermarket roller assembly from a brand like Prime-Line works well, but we replace them in pairs, because one new roller next to one worn roller will hand the door slightly out of plumb within a few months.

To identify what you have, look for the ES Windows label on the door edge or the top rail. If the label is gone, measure the door slab thickness: ES700 is 1-3/8 inches, ES900 is 2-1/4 inches. That measurement alone narrows the parts catalog by half.

Signs Your ES Windows Door Installation Is Failing

• Door drags on the threshold or the strike side of the jamb. Over the years the original shims settle, especially in Fort Lauderdale homes where the slab moves with seasonal groundwater. Shim settlement pulls the frame out of square and puts diagonal pressure on every moving part. A correction often beats a replacement, but only if the door slab itself hasn’t been sacrificed by repeated trimming.
• The bottom sweep is leaving light or water marks on the inside floor. Florida rain hits the north and east exposures hard, and a worn ES Windows sweep lets wind-driven water ride right over the threshold cap. The sweep is a $15 to $40 part, but the subfloor damage from a long-ignored one runs into the thousands.
• The door drops or ‘jumps’ when you open or close it. That’s almost always a hinge barrel that has flattened from the door’s weight. On ES900 doors, the bottom hinge takes the majority of the load, and once the barrel wears oval, the door will never align again without new hinges.
• Hardware feels loose or the handle has started to sag. The set screws walk loose over time, and when a handle sags, the latch no longer sits in the strike plate correctly. Eventually the door won’t latch at all, which is a security problem more than a convenience one.
• The frame has visible rust staining at the corners or along the sill. Salt air is harder on aluminum frames than most manufacturers admit. Once the corner welds show rust bloom, the frame’s structural integrity is compromised, and caulking over it just buys a few months, not years.

Replacement Cost & What’s Included

In Fort Lauderdale, expect to pay $950 to $1,650 for a standard ES700 door install, and $1,600 to $2,400 for an ES900 or a larger opening. The factors that push you toward the high end are the door width, whether the frame is being replaced or reused, any stucco patching required around the jamb, and whether your property sits in a wind-borne debris zone that requires impact-rated glass and heavy-duty hardware to meet Florida Building Code.

You’ll have a written price in your hands before anyone picks up a tool. That price covers the door, hardware, labor, threshold, shims, sealants, and disposal of the old door. It does not change once work starts, unless we open the frame and find damage that was invisible from the outside, and if that happens we stop and show you before spending another dollar. Every installation carries the 365-Day Done Right Promise: if it is not right, we make it right. No argument needed.

DIY or Call Us?

Some jobs are worth doing yourself. Lubricating the hinges with a dry silicone spray, tightening set screws on the handle, and checking that the weep holes on the bottom of the frame are clear are all safe and useful. But once the door is dragging, the frame is out of square, or the hinges have visible wear, call a pro. A door that weighs 150 to 250 pounds can injure you badly if it comes off the hinges while you are working on it, and a door that falls the wrong way takes out more than your afternoon. We have the right lift tools, shim stock, and the experience to get an ES Windows door hung, plumb, and square the first time.

If you are in Fort Lauderdale and the door is starting to fight you, call (754) 354-3671. We’ll give you a straight answer on whether it’s an adjustment, a part swap, or a full replacement, and the estimate is free.

FAQs